Clutch components are subjected to extreme service demands. Cheap parts suffer early failure. We supply genuine BORG and BECK clutch parts. All clutch equipment carries a two-year limited warranty.

Clutch Disc and Pressure Plate
Back to Top

Clutch Alignment Arbor
Series I, II, III, all models	CDAA1

Driven Plate
9" Series I, II, IIa, through 1966	591704
9.5" Series IIa, III	FRC2297

Pilot Bushing, bronze, in flywheel, for gearbox first motion shaft	8566

Pressure Plate
9" Series I, II, IIa, through 1966	591705
9.5" Series IIa, 1967-1971	571228
9.5" Series III	576557

Clutch Hydraulic Equipment
Back to Top

Master Cylinder
Series II, IIa, through 1968, with separate steel reservoir	90569126
Late Series IIa, III, 1969 on, with integral reservoir	550732

Adaptor between clutch master cylinder #550732 and outlet pipe
Late Series IIa, III	139082

Slave Cylinder, at bellhousing
Series II, IIa	266694
Series III	FRC8531

Flexible Rubber Hose, to slave cylinder
Series II, IIa	268341
Series III	NRC2129

Note: STAINLESS STEEL BLEED SCREW is supplied
exclusively by The British Northwest Land Rover Company
for the clutch slave cylinder and all wheel cylinders.

Girling Grease Essential for proper rebuilding and periodic servicing of GIRLING hydraulic cylinders. Minimizes corrosion and early cylinder failure	GLR1230

Girling Hydraulic Fluid
12 ounce bottle	GTLMAP
32 ounce bottle	GTLMAQ

Mechanic's Caution: Use only GIRLING approved
Castrol GT LMA brake fluid or silicone hydraulic fluid.
The hydraulic system will be destroyed by any other brake fluid!

PIPE, Master cylinder to flexible hose.
Series II, IIa	569224
Series III	NRC4222

PIPE, from flexible hose to slave cylinder
Series III only	NRC1655

PIPE, from reservoir to clutch master cylinder
Series II, IIa, through 1968.	562978

Reservior
Series II, IIa, through 1968. Steel. Shared with brake master cylinder Reconditioned	504105R

Clutch Cylinder Rebuild Kits
Back to Top

Rebuild Kit, Clutch Master Cylinder
Series II, IIa, III	8G8837

Rebuild Kit, Clutch Slave Cylinder
Series II, IIa, III	8G8600

Clutch Mechanical Parts
Back to Top

Bushing, Shouldered, Bronze, for throwout bearing.
Series II, IIa	231075

Bushing, Spherical for clutch release shaft
Series II, IIa	217984

Felt Seal for spherical bushing
Series II, IIa, 2 required	217985

Clevis for vertical rod, with pin and spring
Series II, IIa	275199

Clevis Pin for clutch release shaft, specially hardened
Series II, IIa, 2 required	536803

Mechanic's Note: Even the best quality clevis pins are
known to break. We recommend only original equptment parts
and that both pinsbe renewed whenever servicing this critical area.

Clutch Withdrawal Sleeve contacts the pressure plate
Series I, II, IIa	231074
Cross Shaft Series II, IIa, in bellhousing	231943
Bush for cross shaft, shouldered	214794
Bush for cross shaft, plain	214793
Oil Seal for clutch release shaft. Series I, II, IIa	90214787

Oval Blanking Grommet, rubber, for early bellhousing
Series I, II	232604

Push Rod for clutch slave cylinder. Order clevis separately, (above)
Series I, II	537601
Series IIa	576751

Rubber Boot for cross shaft, at bellhousing
Series I, II	236281
Series IIa	553262

Spring, returning clutch release shaft, at slave cylinder
Series I, II, IIa	278690

Back To Parts Catalog Index

HOME